We have established 2 separate support lines, one in US and one in EU. Both can be used, depending on the time.
- techsupport@quintusteam.com, USA
- techsupport@quintusteam.se, EU and Asia
We have established 2 separate support lines, one in US and one in EU. Both can be used, depending on the time.
High Pressure Heat Treatment (HPHTᵀᴹ) is the term used by Quintus for heat treatment in combination with steered heating and HIP processing. The steered cooling capability in Quintus equipment allows heat treatment directly after the densification steps.
HPHTᵀᴹ utilises convection of the HIP pressure medium over cold surfaces inside the HIP vessel. These cold surfaces are made possible through cooling due to the design of the Quintus equipment. The flow of gas can be controlled and directed allowing you to steer cooling at a specific rate. Quintus URC® and URQ® technologies are key in making this possible.
All manner of materials can be heat treated with solutionizing steps in the HIP. Aging can also be performed on hardenable alloys to bring strength up with pore-free microstructures. Ceramic materials such as silicon nitride can also benefit from much higher cooling rates than previously possible. Both of these are helped by the pressure inside the vessel.
Uniform Rapid Cooling, URC®, is a Quintus invention which enables uniform cooling of the payload. Forced convection of high temperature and high pressure gas over a heat sink enables controllable cooling of the gas. URC® is used for metals as well as ceramic materials, to increase productivity and heat treat parts.
Uniform Rapid Quenching, URQ®, is a Quintus invention which enables high speed quenching of the payload, at similar cooling rates to gas quenching. Cold gas in the HIP is exchanged with the hot gas in the furnace at a very high rate, effectively quenching the payload in a uniform way with minimal induced stress.
Flexform is a low-cost sheet metal hydroform technology, ideally suited for low volume production. Flexform use only one single rigid tool half and a flexible rubber diaphragm, backed up by high-pressure hydraulic oil. Typical Flexform production volumes range from a few parts per year and per tool, up to a few thousand parts.
Flexform is since decades well established within the aerospace industry, both for airframe, engine and space sheet metal part production. The aerospace industry request for high quality parts in relatively small volumes of each, at a high variety, make the technology a perfect fit.
The technology is also a great fit for all industries where prototyping and low volume production is required, such as automotive, busses, trucks, yellow goods, food processing equipment, white goods, building façades etc.
Beside the final part quality, the main perceived benefit is the low fabrication cost. This due to the low tool cost involved. The process also allows for several tools and parts to be produced in one and the same forming operation. 50-90% of conventional 2-piece tool cost may typically be saved by using the Flexform technology.
From thin foil up to ~10 mm sheet metal may be formed, typically however thicknesses of 1-5 mm are used, including traditional aerospace aluminum alloys, stainless and most mild steel alloys. Tough alloys such as Inconel and titanium may also be formed.
Within the aerospace industry the use of high-pressure typically reduce, or even eliminate, the need for labor hand correction and the need for intermediate heat treatments.
In all applications the high-pressure support forming of complex and intricate shapes, at excellent repeatability and part quality.
As a science based technology, HPP is not only fully recognized by global regulatory bodies as an antimicrobial process with superior capabilities for inactivating many food pathogens of concern, but also for slowing down the growth of spoilage bacteria, thereby extending refrigerated shelf life between 2-10 times longer than unprocessed foods. Both these benefits alone can have a significant
impact on the global challenges of food safety and food waste.
Most conventional food processing methods such as heat and/or chemicals have negative effects on health and nutrition. Consumers are demanding high nutritional values in foods, particularly those present in fresh, raw, or minimally processed varieties. HPP does not affect nutritional components in foods largely because it has no effects on covalent bonds so HPP products maintain their vitamins and bioactive compounds.
Manufacturers using HPP eliminate chemical preservatives used to control microbial growth and reduce the frequency of food safety testing, thus satisfying the demand from customers for preservative-free foods, while reducing operational costs, hence delivering higher company values. HPP has thus become the process of choice among non-thermal food processing technologies. The
assurance of inactivating foodborne pathogens, post packaging, provides food and beverage manufacturers the business-critical food safety confidence for protecting their consumers, as well as ensuring that their brands and company reputations remain untarnished.
HPP is commercially used in wide range of foods and beverages such as ready-to-eat deli meats, fruit and dairy based drinks, baby foods, dairy products, pet food, ready meals, ready-to-cook marinated meats and meals, seafood, and wide variety of plant-based products including guacamole, hummus, salsa, ready-to-eat salads, tofu and plant-based protein meat analogues.
Most food and beverages are applicable for HPP technology. However, certain intrinsic and extrinsic factors are important in determining HPP conditions and satisfying regulatory rules and guidelines.
We support the customers throughout the complete HPP development process. From recipes to packaging to designing and providing in-house validation services. Our comprehensive evaluation and support is geared for getting your product in the market quickly.
Our Quintus ® Care Program reflects our culture of true partnership, as witnessed by near three quarters of a century pioneering pressure technologies. Your immediate and long term benefits of Quintus ® Care includes controlling ongoing operational costs, guaranteed access to parts, regular technical reviews and remedial training, application support, as well as opportunities to participate in ongoing educational seminars
During HPP the pressure reaches up to 6,000 bar (87,000 psi). At this pressure, products will compress approximately 15% of their volume, meaning that HPP packaging must be waterproof, hermetically sealed, and include materials which are flexible to withstand compressions of at least 15%. For these reasons, different plastic materials have traditionally been a popular choice for HPP since many of these are flexible enough to allow containers to compress without breaking and elastic enough to retake their original shapes after the process. Additionally, several sustainable alternatives can be used with HPP such as rPET, PP, PLA and other biodegradable solutions.
Commonly used packaging and materials for HPP include bottles, cups, pouches, trays, in combination with various types of films or closures. Sealing surfaces for films need to be relatively wide, uniform and preferably flat. Sealability (heat seal strength) is an important element for packaging that is subjected to HPP. Cross-hatched patterns are not suitable as they can allow oxygen
diffusion into the packages that will contribute to oxidative deterioration of products.
We support customer in priority order. Our Quintus care full customers are priority, secondly our Quintus care base customers and after that the broader market. Each Quintus care customer has a Key Account Manager to feed the dialog through Quintus services to you as customers.
Do you want to know more about Quintus care?
Our equipment is reliable. We are the global leader, have 60 years’ experience and our customers in general have very low cost for operating our presses. However, every machine will fail and no one can say which part and when it will fail. Because if so it would be in the maintenance manual. The applied strategy for uptime is:
Studies shows that maintenance cost for a normal machine within the Industrial sector is around 6-7%/year of the investment and our full fledge Quintus Care is normally well below that. The full fledge SLA allows you to control all the cost for the material. Whereas the base agreement leaves the material portion open for sourcing to Quintus on need basis, or towards other suppliers.
Over the years we have developed our service level agreements; Quintus care in two main offers.
The base offer gives you support priority, remote tech support, application support (some countries this cannot be offered to), annual f2f trainings and annual maintenance, safety and reliability inspection.
Quintus care full additionally to the base also includes all spare parts for preventative maintenance, as well as covering spare parts if something unexpected happens (with some exceptions).
Being proactive about maintenance with a Quintus care contract keeps your costs planned and secures the best possible uptime for your system.
Cookie | Duration | Description |
---|---|---|
cookielawinfo-checkbox-advertisement | 1 year | Set by the GDPR Cookie Consent plugin, this cookie records the user consent for the cookies in the "Advertisement" category. |
cookielawinfo-checkbox-analytics | 11 months | This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Analytics". |
cookielawinfo-checkbox-functional | 11 months | The cookie is set by GDPR cookie consent to record the user consent for the cookies in the category "Functional". |
cookielawinfo-checkbox-necessary | 11 months | This cookie is set by GDPR Cookie Consent plugin. The cookies is used to store the user consent for the cookies in the category "Necessary". |
cookielawinfo-checkbox-others | 11 months | This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Other. |
cookielawinfo-checkbox-performance | 11 months | This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Performance". |
CookieLawInfoConsent | 1 year | CookieYes sets this cookie to record the default button state of the corresponding category and the status of CCPA. It works only in coordination with the primary cookie. |
elementor | never | The website's WordPress theme uses this cookie. It allows the website owner to implement or change the website's content in real-time. |
viewed_cookie_policy | 11 months | The cookie is set by the GDPR Cookie Consent plugin and is used to store whether or not user has consented to the use of cookies. It does not store any personal data. |
Cookie | Duration | Description |
---|---|---|
_hjAbsoluteSessionInProgress | 30 minutes | Hotjar sets this cookie to detect a user's first pageview session, which is a True/False flag set by the cookie. |
li_gc | 5 months 27 days | Linkedin set this cookie for storing visitor's consent regarding using cookies for non-essential purposes. |
lidc | 1 day | LinkedIn sets the lidc cookie to facilitate data center selection. |
UserMatchHistory | 1 month | LinkedIn sets this cookie for LinkedIn Ads ID syncing. |
wp-wpml_current_language | session | WordPress multilingual plugin sets this cookie to store the current language/language settings. |
Cookie | Duration | Description |
---|---|---|
_uetsid | 1 day | Bing Ads sets this cookie to engage with a user that has previously visited the website. |
_uetvid | 1 year 24 days | Bing Ads sets this cookie to engage with a user that has previously visited the website. |
Cookie | Duration | Description |
---|---|---|
_ga | 1 year 1 month 4 days | Google Analytics sets this cookie to calculate visitor, session and campaign data and track site usage for the site's analytics report. The cookie stores information anonymously and assigns a randomly generated number to recognise unique visitors. |
_ga_* | 1 year 1 month 4 days | Google Analytics sets this cookie to store and count page views. |
_gat_UA-* | 1 minute | Google Analytics sets this cookie for user behaviour tracking. |
_gcl_au | 3 months | Google Tag Manager sets the cookie to experiment advertisement efficiency of websites using their services. |
_gid | 1 day | Google Analytics sets this cookie to store information on how visitors use a website while also creating an analytics report of the website's performance. Some of the collected data includes the number of visitors, their source, and the pages they visit anonymously. |
_hjFirstSeen | 30 minutes | Hotjar sets this cookie to identify a new user’s first session. It stores the true/false value, indicating whether it was the first time Hotjar saw this user. |
_hjSession_* | 30 minutes | Hotjar sets this cookie to ensure data from subsequent visits to the same site is attributed to the same user ID, which persists in the Hotjar User ID, which is unique to that site. |
_hjSessionUser_* | 1 year | Hotjar sets this cookie to ensure data from subsequent visits to the same site is attributed to the same user ID, which persists in the Hotjar User ID, which is unique to that site. |
AnalyticsSyncHistory | 1 month | Linkedin set this cookie to store information about the time a sync took place with the lms_analytics cookie. |
CONSENT | 2 years | YouTube sets this cookie via embedded YouTube videos and registers anonymous statistical data. |
ln_or | 1 day | Linkedin sets this cookie to registers statistical data on users' behaviour on the website for internal analytics. |
pardot | past | The pardot cookie is set while the visitor is logged in as a Pardot user. The cookie indicates an active session and is not used for tracking. |
Cookie | Duration | Description |
---|---|---|
bcookie | 1 year | LinkedIn sets this cookie from LinkedIn share buttons and ad tags to recognize browser IDs. |
bscookie | 1 year | LinkedIn sets this cookie to store performed actions on the website. |
li_sugr | 3 months | LinkedIn sets this cookie to collect user behaviour data to optimise the website and make advertisements on the website more relevant. |
MUID | 1 year 24 days | Bing sets this cookie to recognise unique web browsers visiting Microsoft sites. This cookie is used for advertising, site analytics, and other operations. |
test_cookie | 15 minutes | doubleclick.net sets this cookie to determine if the user's browser supports cookies. |
visitor_id* | 1 year 1 month 4 days | Pardot sets this cookie to store a unique user ID. |
visitor_id*-hash | 1 year 1 month 4 days | Pardot sets this cookie to store a unique user ID. |
VISITOR_INFO1_LIVE | 5 months 27 days | YouTube sets this cookie to measure bandwidth, determining whether the user gets the new or old player interface. |
YSC | session | Youtube sets this cookie to track the views of embedded videos on Youtube pages. |
yt-remote-connected-devices | never | YouTube sets this cookie to store the user's video preferences using embedded YouTube videos. |
yt-remote-device-id | never | YouTube sets this cookie to store the user's video preferences using embedded YouTube videos. |
yt.innertube::nextId | never | YouTube sets this cookie to register a unique ID to store data on what videos from YouTube the user has seen. |
yt.innertube::requests | never | YouTube sets this cookie to register a unique ID to store data on what videos from YouTube the user has seen. |
Cookie | Duration | Description |
---|---|---|
lpv228122 | 30 minutes | Description is currently not available. |
VISITOR_PRIVACY_METADATA | 5 months 27 days | Description is currently not available. |